(c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Compliance Approved 2.4 GHz RF Transceiver Modules with Built-In RFDP8 Application Protocol Complete Compliance Approved & Certified, READY-TO-USE, 2.4 GHz wireless solution with built-in RFDP8 interference-tolerant user application protocol. Includes RFID, 32 Bit ESN, Logic Switch Transmitter / Receiver, 9600-8N1 Serial UART Transceiver and many easy-to-use addressable network modes. No development required at all, no RF layout, no code writing, all features are built-in. Be up and running with a wireless solution in minutes. RFD21733 IC & FCC APPROVED CE * ESTI TESTED & COMPLIANT Easy to solder 0.050 Inch SMT pads RFD21735 Optional Configuration CE * ESTI For use with any External Antenna 500 Foot Range 15mm x 15mm (0.600 x 0.600 Inch) KEYFOBs & RFID IC * FCC APPROVED RFDANT * RFD21743 FCC APPROVED Simple Drill Hole Mount rw Standard RFDP8 Interface No Need for RF cables. Only +3V * GND * Data. 1.5mm 11pin Connector. Fits onto any PCB. SMT or Through Hole. CE * ETSI Compliant Standard & Custom CE * ESTI TESTED & COMPLIANT Complete RADIO INSIDE Use any plastic or metal enclosure. Antenna Patents Pending 2,000 FOOT ULTRA LONG RANGE Free Applications Support * Email your application questions to support@rfdigital.com 1 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs KEYFOBs The RFD21733 Module with its RFID interval factory set to 30 seconds is inside of a KEYFOB enclosure with a CR2032 battery. The reference layout for this device is available through support@rfdigital.com if you want to build it yourself. However if you wish to purchase the ready-made KEYFOBs from RF Digital they are available, part numbers shown below. There are two modes of use, one is in Active RFID mode were the KEYFOB automatically transmits its ESN once every 30 seconds. The other mode of use is SWITCH transmitter, which is available in 1, 2 or 3 buttons. The RFID versions also have 1, 2 or 3 buttons so they serve as an automatic RFID transmitter and in addition have the switch buttons in one KEYFOB. If you do not need the automatic Active RFID feature, just use the Switch Button KEYFOBs. Rotatable Buttons Rotatable Buttons RFD21783 RFD21793 3 Button Switch Keyfob 3 Button RFID Keyfob Pressing button 1, 2 or 3 will cause the output 1, 2 or 3 on the RFD21733 Module or RFD21743 / RFD21732 RFDANT to go high for the duration the button is pressed, when in one of the 4 switch modes. If in Serial UART mode, then you will receive 1 byte representing which button is pressed or if RFID transmission and 4 more bytes indicating the 32 bit unique ESN of the KEYFOB. RFD21782 RFD21792 2 Button Switch Keyfob 2 Button RFID Keyfob Pressing button 1 or 3 will cause the output 1 or 3 on the RFD21733 Module or RFD21743 / RFD21732 RFDANT to go high for the duration the button is pressed, when in one of the 4 switch modes. If in Serial UART mode, then you will receive 1 byte representing which button is pressed or if RFID transmission and 4 more bytes indicating the 32 bit unique ESN of the KEYFOB. RFD21781 RFD21791 1 Button Switch Keyfob 1 Button RFID Keyfob Pressing button 2 will cause the output 2 on the RFD21733 Module or RFD21743 / RFD21732 RFDANT to go high for the duration the button is pressed, when in one of the 4 switch modes. If in Serial UART mode, then you will receive 1 byte representing which button is pressed or if RFID transmission and 4 more bytes indicating the 32 bit unique ESN of the KEYFOB. Free Applications Support * Email your application questions to support@rfdigital.com 2 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs TYPICAL RANGE Range results need to be tested for every application and scenario. RF Digital's range tests are done line-of-sight and outdoors in a typical city street setting. You should use these typical range test results as a point of reference, until you can conduct your own range tests in your own test environment. If you have any questions, always feel free to contact RF Digital Support at support@rfdigital.com LONG RANGE MODULE 500 MODULE FOOT RANGE RFD21733 150 Meters RFD21733 LONGER RANGE MODULE 1,000 RFDANT FOOT RANGE RFD21733 300 Meters RFD21743 RFD21742 ULTRA LONG RANGE RFDANT 2,000 RFDANT FOOT RANGE RFD21743 RFD21742 600 Meters Free Applications Support * Email your application questions to support@rfdigital.com RFD21743 RFD21742 3 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs TYPICAL APPLICATIONS * Active RFID * Long Range RFID * Remote Control * Light Controls * Home Automation * Alarm Security * Keyless Entry * Perimeter Monitoring * PC Keyboard Security * Wireless Keyboard * Wireless Mouse * TV Remote * Home Stereo Remote * Asset Tracking * Wireless PTT * Remote Switches * Remote Terminals * Wireless RS232 DB9 * Wireless RS485 * Temperature Control * HV/AC * Meter Reading * Data Acquisition * Inventory Control * Keyfob Remotes * Industrial Controls * Vending Machines * Pan-Tilt-Zoom Control * Camera Flash Control * Biometrics * Seismic Monitoring * M2M & many more... LONG RANGE KEYFOB / RFID 350 MODULE FOOT RANGE RFD21783 RFD21782 RFD21781 RFD21793 RFD21792 RFD21791 100 Meters RFD21733 LONGER RANGE KEYFOB / RFID 700 RFDANT FOOT RANGE RFD21783 RFD21782 200 Meters RFD21743 RFD21742 RFD21781 RFD21793 RFD21792 RFD21791 Free Applications Support * Email your application questions to support@rfdigital.com 4 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs PINOUTs There are 11 total active signal pins including power and ground for both MODULEs and RFDANTs. The MODULEs have 7 additional ground pins. Also the MODULES have one extra pin for a total of 19 pins, this is pin 11, which applies only to the RFD21735 which is for external antenna, however the RFD21733 pin 11 is a no-connect since it has a built-in antenna. RFD21733 * RFD21735 MODULEs RFD21733 RFD21735 There are a total of 8 ground pins, you only need just one ground pin for an electrical connection to make the module function. The additional ground pins are for convenience and also performance with layout configurations. The pin 12, 10 and 9 are recommended to always be connected since they help provide some ground area for the module as well as on the opposing side of the antenna. However just one single ground out any of the 8 GND pins are adequate for proper function. RFD21742 * RFD21743 RFDANTs RFD21742 RFD21743 The black wire (ground) is pin #1, the red wire (+V) is pin #2, and so on. See pinout on left side. Free Applications Support * Email your application questions to support@rfdigital.com 5 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com FEATURES * Runs on a single coin cell for years. * WiFi interference tolerant. * Heavy 2.4 GHz noise and interference tolerant. * Motor noise and interference tolerant. * Very low cost. * No external parts required. * No RF layout required. * Easy and ready-to-use, hand-held, eval and application boards available. * Ultra small 15mm x 15mm footprint (RFD21733/RFD21735) * Fully contained, truly finished, ready to use module. * CE / ETSI / IC & FCC Certified and Approved. * Typical range: 500 feet (150 meters): RFD21733 MODULE. * Typical range: 2,000 feet (600 meters): RFD21742 and RFD21743 RFDANTs. * Worldwide 2.4GHz ISM band operation. * User configurable without need for any programming. * 2uA Ultra low power modes. * Only 14mA current consumption at 0dbm TX and 17mA at RX. * 16 bit CRC data accuracy verification built-in. * 32 bit unique factory ESN in every module (4 billion combination security). * Flexible network modes, including broadcast and individual addressing. * Optional version available for use with external antenna (RFD21735). * Switch on/off, logic, remote-control without the need for an external controller. * Switch nodes individually addressable without the need for an external controller. * Wide supply range +1.9V to +3.6V. * Built-in, high performance internal miniature antenna (RFD21733). * Peer to Peer (Ad-Hoc) networks and configurations. * Point to Multi-Point networks and configurations. * Multi-Point to Multi-Point networks and configurations. * Selective addressing of any module by using factory built-in ESN. * Fast-turn-around, minimal latency (20 millisecond). * Patent pending RFDP8 interference tolerant protocol. * Full application protocol runs transparent to the user. * Easy to use, simple to design in. * Stores up to 60 ESNs (Electronic Serial Numbers) for network modes. * Many to one data modes ideal for multi-point data acquisition. * Unlimited number of module nodes can communicate to each other. RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs CUSTOM Modules RF Digital's RFDP8 application firmware loaded into the MODULEs or RFDANTs can be customized to fit application specific requirements. RF Digital can design and manufacture fully custom modules to fit your needs. If you do not find what you're looking for, feel free to contact RF Digital with your requirements. Email: support@rfdigital.com FAST Support For free RF layout design reviews, send color screen captures of your layout to support@rfdigital.com, you will save time and money before you fab your boards. Our FAST RESPONSE Support Team welcomes your questions! RFDP8 Application Protocol * Mode Selector Chart Free Applications Support * Email your application questions to support@rfdigital.com 6 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Choosing between RFD21733 Module or RFD21743 RFDANT The RFD21733 RF Module and the RFD21742 / RFD21743 RFDANTs have the same electrical interface and are both embedded with the Patent Pending RFDP8 interference immunity protocol. They are pin for pin electrically compatible. Except for the different form factor, cost and range, they are basically the same. The RFDANTs have an 8 inch long 1.5mm, 11pin connector termination for its interface to your electronics, were the RFD21733 module has a 19 pin SMT interface and solders to your PCB. Only 11 out of the 19 pins are used for electrical interface. The RFD21733 is only 15mm square and has a range of about 500 feet. The RFD21733 module is about one quarter the cost of the RFDANT. So why would you use the RFDANT? There are many reasons: The RFDANT is hermetically, fully potted and over-molded, has an industrial rugged enclosure and the full radio system and processing is all built into the Antenna structure itself. The RFDANTs mounting does not require a PCB at all, simply just drill a hole into your enclosure and feed the 8 inch cable through and apply a nut and your RFDANT is mounted and ready for use. The RFDANT does not have impacts from proximity effects from near-by metal enclosures and objects. The RFDANT has a perfect antenna pattern which provides extraordinary, consistent repeatable performance. The RFDANT's Revolutionary Patent Pending design enables it to reach distances of 2,000 feet, while still being an Ultra Low Power device. This huge range is reached without any power amplifiers at all, it's unique design is responsible for it reaching these great distances without any extra battery drain or extra power. The RFDANT makes it easy for you to satisfy GREEN directives due to its unique design and ultra high performance. The RFDANT fits in the palm of your hand and looks like an Antenna, but of course it is much more since it is the whole radio and processing system in one unit. There are no RF cables at all, simply connect +V, GND, and a few logic signal wires based on your application and you are done. There is no need for PCB layout either. You can directly connect to the 11 pin, 8 inch cable extending out of the bottom of the RFDANT. The RFD21733 is an ideal partner with the RFD21743 or RFD21742 RFDANTs. They can communicate with each other using the RFDP8 protocol with switch logic IO or Serial UART. You can mix and match them as well, with using RFD21733 on one end of your system and an RFDANT on the other. The RFD21733 is a perfect fit when you need ultra small size and ultra low cost, and the RFDANT is an ideal solution when you need ultra long range and do not want to place any parts onto your PCB. Even if you will not be using the RFDANT for your application, it is still highly recommended to place the 11 pin connector footprint on your PCB for the RFD21733 so you can have the option to simply plug in the RFDANT for testing during your proto phases, or if you happen to have a customer come to you and ask for more range, you can simply give it to them by not soldering the RFD21733 and instead plugging in the RFD21742 or RFD21743 RFDANT. If you have further questions about the trade offs between the Modules and the RFDANTs, always feel free to contact support@rfdigital.com were you will find very quick and helpful answers to your questions. RFD21733 Module Solders to your PCB with its SMT pads. RFD21742 or RFD21743 RFDANT Plugs into your PCB using its 8 inch long cable. Free Applications Support * Email your application questions to support@rfdigital.com 7 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Differences between RFD21742 and RFD21743 RFDANTs The RFD21742 and RFD21743 are 100% identical hardware, the only difference between the two is firmware loaded at the RF Digital factory. The RFD21742 is in compliance with CE / ETSI emission requirements and is not for FCC. The RFD21743 is in compliance with CE / ETSI emission requirements and is FCC Certified and Approved. The high performance of the RFDANT for FCC requires it to work in a 50% duty cycle mode, which means that when you are running it in its 9600-8N1 UART mode, you can send up to 24 bytes in a row and then you must wait a minimum of 24 byte lengths which is about 24mS before you send up to another 24 bytes. For example you can also send 12 bytes, wait 12mS and then send 12 bytes again, effectively yielding a 50% duty cycle. Note this is only a transmit limitation with the RFDANT, it is not related to receive, so if you have a RFD21733 sending 100% duty cycle at full speed, you can receive that with either RFDANT and it will be fine. But when you go to transmit, if you are using the RFD21743 you will need to use a maximum of a 50% duty cycle for the USA and FCC. However when using the RFD21742 which is for Europe and the CE / ETSI markets, there is no duty cycle limitation. That is the reason there are two part numbers for the RFDANT, the RFD21743 is 50% UART duty cycle for FCC and the RFD21742 is CE and ETSI with 100% duty cycle. So if you plan on selling into the USA market place, then use the RFD21743, if you are Europe ONLY, then you can use the RFD21742. Also, of course you can use the RFD21743 for USA and Europe. If you are sending in switch mode using the RFD21742, it will send a new packet every 16mS and the hang time for a switch receiver in mode 6 or 7 is 50mS. Where with the RFD21743 it will send a new packet every 24mS to work within the 50% duty cycle limit for FCC and IC. If you require Canada (IC) Approval for the RFD21743, please contact sales@rfdigital.com. The impact with switch mode is hardly even noticed between the RFD21743 and RFD21742. Most common applications are typically with burst data less then 24 bytes per burst, so the difference between the RFD21743 and RFD21742 is negligible, nevertheless the choice is still available for you and they are pin for pin compatible. Once you test an RFDANT, you will be truly amazed with its performance. FCC CE * ETSI CE * ETSI RFD21743 RFDANT RFD21742 RFDANT Plugs into your PCB using its 8 inch long cable. Plugs into your PCB using its 8 inch long cable. Free Applications Support * Email your application questions to support@rfdigital.com 8 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Revolutionary RFDANT Advantages The RFD21743 and RFD21743 RFDANT are full 2.4 GHz radio transceivers including the RFDP8 protocol, completely built into an antenna form factor allowing the entire radio transceiver to be outside your product, where only the power and signal cable will extend into your product enclosure to then be connected to your PCB with a simple 1.5mm SMT or THROUGH HOLE connector. The RFD21742 and RFD21743 is functionally identical to the RFD21733 module and the RFD21772 and RFD21733 Eval Boards work just like the RFD21737 Eval Board except it has an 11 pin 1.5mm connector on it so the RFD21742 or RFD21743 RFDANT can plug into it. The RFD21772 is the Eval board for the RFD21742 and the RFD21773 is the Eval board for the RFD21743. The RFD21772 and RFD21773 each include one RFDANT. You need a pair for a complete system. The RFD21742 and RFD21743 RFDANTs have been range tested at 2,000 feet which is 4x the range of the RFD21733 which is at 500 feet. No special PCB layout is needed for the RFD21742 or RFD21743 RFDANT, simply just put a connector on your PCB and you are done . All this substantial range increase is achieved all without any increase in current or battery consumption. The RFDANT is RF Digital's Patent Pending Radio Inside Antenna product, which is a complete radio transceiver and antenna mounted inside of an antenna enclosure, suitable for mounting to virtually any type of end-product, regardless if the enclosure is plastic, metal, glass, really any material. The entire radio transceiver is mounted inside the antenna enclosure, so there is no loss of RF power to the antenna from the module, and results in the most effective power transfer ratio possible, providing lowest power consumption possible to achieve a specific range. The radio being inside of the antenna and outside the enclosure allows for more room inside the enclosure for the designers application electronics. Minimal interference with the internal electronics of the enclosure results in better range and performance of the wireless system. The actual effective antenna is pushed away from the enclosure, which reduces the effect of holding the enclosure, therefore improving the performance, range and predictability of the users wireless system. Logic level signals are communicated through an unshielded cable (not coax) to the RFDANT, which can be run for long distances without any loss to the performance of the wireless transceiver. By the antenna and module being fully outside allows for easy retrofit of nearly any product due to it not consuming any internal space inside the enclosure, drill a hole and screw it in, add a nut inside to secure it and wire the logic level signals to your electronics. Mount on metal or plastic enclosures with no worry about ground effects. Stable Antenna Pattern providing substantial, well-distributed, passive-gain for transmit and receive, results longer repeatable range from your wireless system. For free Schematic and Layout design reviews, send color screen captures or PDFs of your schematic and layout to support@rfdigital.com. RF Digital's Support and Application Engineers are ready to help you get your wireless application running to today. Just send your application questions to support@rfdigital.com and receive direct, fast and accurate answers. We look forward to helping you!!! Free Applications Support * Email your application questions to support@rfdigital.com 9 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFDANT * RFD21742 * RFD21743 * Compliance Approved RFDANT * RFD21742 * RFD21743 * Mating Connectors Mating connectors for the 11 pin RFDANT can be found at Digikey in the USA at: http://www.digikey.com or at any other JST distributor. They are standard connectors and you may use other manufacturers. 1) a. b. Top Entry, Through Hole Type, 11 pos Digikey P/N 455-1666-ND Manufacturer P/N: B11B--ZR 2) a. b. Side Entry, Through Hole Type, 11 pos Digikey P/N 455-1678-ND Manufacturer P/N: S11B--ZR 3) a. b. Top Entry, SMT Type, 11 pos Digikey P/N 455-1690-2-ND Manufacturer P/N: B11B--ZR-SM4-TF 4) a. b. Side Entry, SMT Type, 11 pos Digikey P/N 455-1701-2-ND Manufacturer P/N: S11B--ZR-SM4-TF Free Applications Support * Email your application questions to support@rfdigital.com 10 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFDANT * EXCELLENT ANTENNA PATTERNS 51 52 53 54 1 -20 2 3 4 5 50 6 -30 49 7 48 8 47 9 -40 46 10 -50 45 11 44 12 -60 43 13 42 RFDANT RFD21742 and RFD21743 high performance antenna patterns are easily achieved without any RF considerations or knowledge because the 11 pin cable and connector only carries power and data signals so NO RF cable loss at all. RF Digital's Patent Pending RFDANT design is the only device in industry which can achieve this outstanding performance. 14 -70 41 15 40 16 39 17 38 18 37 19 36 20 35 21 34 22 33 23 32 31 30 29 28 27 26 24 25 Horizontal Antenna Pattern 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 55 56 57 60 58 59 -20 1 2 3 4 5 6 -30 7 -40 -50 -60 -70 37 36 35 34 33 32 31 28 30 29 27 26 25 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Vertical Antenna Pattern Free Applications Support * Email your application questions to support@rfdigital.com 11 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21772 & RFD21773 Eval Boards for RFDANT RFD21772 / RFD21773 Eval board with RFDANT 11 pin connector. RFD21772 / RFD21773 Eval board with RFDANT cable plugged into the 11 pin connector. RFD21772 Eval Board for RFD21742 RFDANT When ordering part number RFD21772, you receive an RFDANT eval board pictured below AND you also receive an RFD2142 RFDANT. For Eval board usage instructions, see sections below. RFD21773 Eval Board for RFD21743 RFDANT When ordering part number RFD21773, you receive an RFDANT eval board pictured below AND you also receive an RFD2143 RFDANT. For Eval board usage instructions, see sections below. Free Applications Support * Email your application questions to support@rfdigital.com 12 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21773 * RFD21743 * RFDANT * Dimensions Flexible RFDANT cable does not have any shielding due to its revolutionary design and therefore does not need it. The 11 conductor cable is flexible and can easily confirm to fit your enclosure. Simply drill hole into your enclosure, insert the RFDANT and you have instant excellent range performance. Free Applications Support * Email your application questions to support@rfdigital.com 13 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21733 * RFD21735 * RFD21742 * RFD21743 * Usage Examples RFD21733 * RFD21735 * RFD21742 * RFD21743 * Applications Free Applications Support * Email your application questions to support@rfdigital.com 14 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21733 * RFD21735 * RFD21742 * RFD21743 * Applications Free Applications Support * Email your application questions to support@rfdigital.com 15 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21733 * RFD21735 * RFD21742 * RFD21743 * Applications Free Applications Support * Email your application questions to support@rfdigital.com 16 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Differences Between Module Eval Boards RFD21737 The RFD21733 RF Module with built-in chip antenna is soldered onto the RFD21737 eval board. The antenna is self-contained within the module. This eval board is self-contained and does not require an external antenna. RFD21738 RFD21739 The RFD21735 RF Module is soldered onto the RFD21738 eval board. There is a 1.2 inch wire antenna soldered onto the RFD21738 which connects to the RFD21735 external antenna pin through RF strip-line within the PCB layers. The RFD21735 RF Module is soldered onto the RFD21738 eval board. There is a FEMALE SMA connector soldered onto the RFD21738 which allows the user to connect to an external 2.4 GHz antenna of their choice. The RFD21735 external antenna pin is routed to the SMA connector through strip-line within the PCB layers. This eval board requires a user supplied 2.4 GHz antenna with a MALE SMA connector. ANTENNA NOT INCLUDED This eval board is self-contained and does not require an external antenna. RFD21737 RFD21738 RFD21739 RFD21737 RFD21738 RFD21739 RFD21737 RFD21738 RFD21739 Free Applications Support * Email your application questions to support@rfdigital.com 17 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Eval Board Top and Bottom Labeled Views All 5 Eval Boards, including the RFDANT boards can be powered from their on-board CR2032 3V battery or through the 12 pin 0.100 inch (2.54mm) pitch header, which can plug into directly into standard solderless breadboards or connect to mating a 0.100 inch (2.54mm) mating socket. The Eval Boards can work as stand-alone or can be wired to your application. The RFDANT Eval Boards have an RFDANT 11 pin connector instead of a Module. Free Applications Support * Email your application questions to support@rfdigital.com 18 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFDP8 Mode Selector Switch for all 5 Eval Boards The 8 different modes of the RFDP8 Application Protocol are selected using the 3-position dip-switch S5 shown in the examples below. The 3 inputs have resistor pull-downs to ground, so when the switch is in its OFF (open) position, there is a low (0) on the input. When the switch is in its ON (closed) position, it connects the input to +V, which produces a high (1). The proper way to read binary is MSB on the left and LSB on the right. Switch manufacturers label the switches from left to right and furthermore they commonly start with 1 rather then 0. So careful attention needs to be given to identify the switch positions. The binary is read from MSB to LSB, rather than LSB to MSB as shown in the examples below. To remove all doubt, only follow the examples shown below. Mode 0 Mode 1 Mode 2 Mode 3 Active RFID Transmitter 3-Input Switch Logic Transmitter Serial UART Transceiver 9600-8N1 Serial UART Transceiver 9600-8N1 Network ON OFF OFF OFF ON OFF OFF OFF ON ON OFF OFF Mode 4 Mode 5 Mode 6 Mode 7 3-Output Switch Logic Receiver 500ms Hang Time 3-Output Switch Logic Receiver 500ms Hang Time Network 3-Output Switch Logic Receiver 20ms Hang Time 3-Output Switch Logic Receiver 20ms Hang Time Network ON OFF OFF ON ON OFF ON ON ON ON ON OFF Free Applications Support * Email your application questions to support@rfdigital.com 19 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Eval Board Top and Bottom View Pinout for All Eval Boards Eval Board Power Supply and Logic Levels - Important There is an internal 3.3 Volt (LDO) on the eval boards. At the (pin 2) +V input pin, you can supply 2.1VDC minimum and a maximum of 3.6VDC. When your supplied voltage is between 3.4V and 3.6V the internal regulator is in regulation and the internal supply to all parts will be 3.3V, and all signals on pins 9-12 will be at 3.3V logic. When 2.1V to 3.4V is supplied the internal 3.3V regulator is of regulation and tracks the input voltage (minus about 100mv overhead). If you supply 2.5V your logic will be at 2.4V, and if you supply 2.1V your logic will be at 2.0V. The internal 3.3V regulator accept up to a 5V supply input, but at 5V supply, your logic levels on pins 9-12 will be at 3.3V, SO USE CAUTION. So you will need to use 3.3V to 5V logic level shifters to run properly at 5V or you will cause damage to the module. When using a 5V supply, a very quick 5V level shifter method (not to be used for production) just for testing, which works in some cases would be to use a 22K resistor in series between the eval boards 3.3V logic and your 5V logic. There is a 47k pull down resistor internal to the Eval Boards ONLY (NOT THE MODULE or RFDANT) on pin 9-12 and this is just enough to switch the logic levels in both directions for a quick and dirty level shifter. There are NO 47k pull down resistors on the Modules or RFDANTs, so you must add your own pull-downs or pull-ups accordingly. Free Applications Support * Email your application questions to support@rfdigital.com 20 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RF Modules and RFDANTs run on 3V Logic Levels (1.9V to 3.6V) The RFD21733, RFD21735, RFD21742 and RFD21743 all run on a supply of 1.9V to 3.6V. They have an internal voltage regulator which is set to 1.8V and it is an LDO so you only need about 100mV of overhead to keep it in regulation. Most circuits which will interface with these devices will be 3V or 3.3V typical, so we will use those voltages for reference in this section. If your circuit runs on 2.5V, 3V or 3.3V, then no problem, you can directly apply supply voltage of 2.5V, 3V or 3.3V to the Module or RFDANT and all your logic signals will be at 2.5V, 3V or 3.3V for a direct interface with your hardware. However if your circuit is running at a higher voltage such as 5V, then you need to use a level shifter IC or a circuit which will translate the Module or RFDANT signals from 3V to 5V for your circuit, and also the 5V from your circuit to the 3V for the Module or RFDANT. Of course you will also need a regulator to drop from 5V down to 3V for the Module or RFDANT. Simple 5V to 3V Logic Level Shifter for prototyping ONLY. If you want a quick an dirty, temporary solution to interface the 3V RF Module or RFDANT to your 5V logic circuit, then you can use a simple resistive divider to get your prototype up and running quickly with just a couple resistors. First, you must supply a regulated 3V or 3.3V to the RF Module or RFDANT using a voltage regulator. Now regarding the logic signals, you can connect a 47k pull down resistor to the logic lines on the following 6 signals, Mode Select 1, Mode Select 2, Learn / Status, IN1 / OUT 1 / LOGIC IO, IN2 / OUT2 / RXD, IN3 / OUT3 / TXD. The RESET has an internal 3.3K pull up and does not apply to this option, and the Mode Select 0, at power up has an internally switched 13k resistor and also does not apply to this option. After connecting the 47k pull down resistor on the Module or RFDANT pins, then use a 22k series resistor to connect the six Module or RFDANT logic pins mentioned above to your 5V device. That will create a 2/3 voltage divider from your 5V device to the 3V RF Module or RFDANT when the 5V device is driving 3V device. When the 3V device is driving the 5V device, there is no divider in that direction, only a 22k series resistor into a high-Z input on the 5V side, so the 5V side will see the full 3V logic, and that is in most cases, just enough to cause a logic high for a 5V logic input. Note this is not a production solution, its just a quick-and-dirty way to get a 5V logic circuit to work with a 5V logic circuit for prototyping. Of course once you have hooked this up and if it does not work for you, do measure the logic levels using a scope on both 5V and 3V nodes to make sure they are actually at sufficient levels to meet the minimums for logic levels for the specific device. Note if you do not have a high-Z input on the 5V side, this will not work. At first chance, when possible, use a proper level shifter capable of sinking and sourcing current and able to do fast switching as this circuit is very limited with its scope of value and use. The Eval Boards have a 47k pull down resistor mounted on the above six referenced pins, so if you are using an Eval Board then all you need is the series 22K resistor (don't add an additional 47k resistor or it will not work), but if you are using the RF Module or the RFDANT WITHOUT the Eval Board, then you will need to add the 47k resistors. Free Applications Support * Email your application questions to support@rfdigital.com 21 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Eval Board Example with internal 47k resistor. RS232 Level Shifter Interface To connect to an RS232 port (9600-8N1), you must use a level shifter to shift the voltage levels from RS232 levels to 3V or 3.3V logic. There are many ICs which can perform that task all in one chip. For example the MAX232, MAX202 or the ICL3321. If you want to connect to a PC you can use this method or you can use a USB port and connect through a virtual communication port shown in the next section. You can use this same interface when connecting to the Eval Boards. Very important, make sure you pull down the Logic IO signal to ground through a 47k resistor if it is not in use, note it is bi-directional so you must use a pull down. FTDI USB Virtual Communication Interface FTDI manufactures a 3.3V Logic Serial Interface cable which plugs into a USB port and shows up as a COMM port on your PC, through which you can connect to PC terminal programs like Hyper Terminal, RealTerm and others. You can purchase the FTDI cable from Digikey.com or other distributors. The manufacturer part number is TTL232R-3V3 and the Digikey Part Number is 768-1016-ND (picture shown below). For international orders, if you want to save on shipping, you can ask for this item to be packed in with your order to RF Digital. Free Applications Support * Email your application questions to support@rfdigital.com 22 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs When using the FTDI USB Interface Cable TTL-232R-3V3, the connections to the RFD21737, RFD21738, RFD21739, RFD21772, RFD21773 Eval Boards are very simple. You only need 4 wires and the Eval Board is also powered from the USB port through the cable. The 3V3 part of the part number for the cable means that the logic levels of the cable are 3.3V. IMPORTANT: The RED wire supplies +5V, and can ONLY be connected to the Eval Boards since the Eval Boards have an onboard 3.3V regulator. You can NOT connect +5V to the Module or RFDANT directly. This is ONLY intended for the Eval Board. The 4 wires you need from the cable are: RED is +5V BLACK is GROUND YELLOW is TXD Data Input to the PC USB Port. ORANGE is RXD Data Output from the PC USB Port. FTDI Cable to RFD Eval Boards: RED - connect to RFD Eval Board Pin 2 and Pin 3 (Pin 2 is power on. Short pin 2 and pin 3.). BLACK - connect to RFD Eval Board Pin 1. YELLOW - connect to RFD Eval Board Pin 11, which is the RXD Data Output of the Eval Board. ORANGE - connect to RFD Eval Board Pin 12, which is the TXD Data Input of the Eval Board. FTDI TTL-232R-3V3 USB Cable wired to RFD Eval Board FTDI TTL-232R-3V3 USB Cable Free Applications Support * Email your application questions to support@rfdigital.com 23 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Free Schematic, Layout and Application Design Reviews For free Application, Schematic and Layout design reviews, send color screen captures or PDFs of your schematic and layout to support@rfdigital.com. RF Digital's Support and Application Engineers are ready to get your wireless application running today. Why spend lots of time reading volumes of data? Instead, simply send your application questions to support@rfdigital.com and receive direct, fast and personal answers focused on your specific project and needs. We look forward to hearing from you!!! FCC Compliance Information The RFD21733 is IC and FCC Modular Approved and Certified, therefore for use of the RFD21733 module in your product does not require further IC or FCC testing. Detail instructions and IC and FCC notices shown later in this data sheet. Any modifications made to the RFD21733 will void the IC and FCC Approval and Certification. The RFD21733 has an integrated on-board chip antenna. You simply include the RFD21733 in your product and follow the IC and FCC notices and information below and place the appropriate label on your product to indicate that it includes an IC and FCC approved module and no further testing would be required for the module. The RFD21735 is NOT IC or FCC Approved. However it is exactly the same as the RFD21733 except it does not have an internal antenna and is built to allow a user to apply their own antenna of choice. Any type of 2.4 GHz antenna may be used. Once you include the RFD21735 into your product and your chosen antenna is connected, then your whole product is tested by an approved IC or FCC compliance laboratory and you receive your own grant for your whole product which includes the RFD21735. This procedure is somewhat costly and time consuming and therefore the RFD21733 is the primary choice by many engineers. The RFD21735 is typically used if you must have an external antenna, however we always recommend first looking at the RFD21743 which already has an FCC Approval and is in the form of an external antenna. The RFD21743 is FCC Modular Approved and Certified, therefore for use of the RFD21743 module in your product does not require further FCC testing. Detail instructions and FCC notices shown later in this data sheet. Any modifications made to the RFD21743 will void the FCC Approval and Certification. The RFD21743 has an integrated antenna. You simply include the RFD21743 in your product and follow the FCC notices and information below and place the appropriate label on your product to indicate that it includes an FCC approved module and no further testing would be required for the module. The RFDANT RFD21743 is a great alternative to needing to get your own FCC approval with the RFD21735 combined with your own antenna. The RFD21743 has an excellent antenna pattern which provides about 4 times more range than a RFD21733 and does not require mounting to your PCB since it has its own antenna enclosure. More details about it below in this data sheet. It should be considered before starting your design with an RFD21735 and your own external antenna, since it accomplishes the same task without the need for further compliance approvals. CE, ETSI Compliance Information The RFD21733, RFD21735, RFD21742 and RFD21743 are CE (ETSI) Tested. See declaration of conformity later in this document. RFDP8 Firmware RF Digital offers firmware for the RFD21733, RFD21735, RFD21742, RFD21743 which meet many common user requirements. The firmware and a unique identifier are pre-programmed and tested at the factory. The programmed module is therefore immediately ready for use upon delivery. Free Applications Support * Email your application questions to support@rfdigital.com 24 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs The RFDP8 firmware use the 3 mode select inputs to select the operating mode. These inputs are sampled when the module powers-on. Some of the operating modes have additional options which are described in the section for that mode. The RFDP8 firmware cannot be modified by the user. For applications that require alternative functionality, contact RF Digital for information about custom firmware to fit your specific requirements. RFDP8 Interference Immunity Algorithm RF Digital's RFDP8 proprietary patent-pending frequency agility protocol operates in the internationally accepted 2.4 GHz band. The RFDP8's leading-edge advanced algorithm is not burdened by a heavy-weight stack as is BlueTooth, ZigBee, WLAN and other protocols, which are well suited for cross-manufacturer interoperability. The RFDP8 protocol is highly robust and effective where there is a need to penetrate through a high saturation of RF noise which is common in nearly all environments today. It is especially effective and can easily coexist in heavy WiFi environments, which very few technologies can do successfully without the need of excessive processing power. The protocol strategically changes channels frequently to deliver its payload to the destination device reliably, yet not too excessively as to demand too much internal processing power which allows it to run with a very low current consumption profile and fast start up times allowing substantial flexibility with implementation. The RFDP8 protocol reduces the amount of on-air traffic and unnecessary chatter due to its unique and highly efficient design, which does not require bilateral registration and association as do many other technologies today. The RFDP8 does not require ack-nacks to complete a packet delivery, its unique technique of packet delivery, recovery and correction allows it to work as a one-way link, hence drastically simplifying users' applications which always results in more a robust wireless system. The RFDP8 protocol combined with RF Digital's leading-edge RF Module hardware delivers a highly robust method of delivering user data from point to point, point to multi-point or multi-point to multi-point, transmitter-receiver, transceiver, serial or switch on/off data modes. The protocol is designed to work seamlessly with RF Digital's hardware modules, the combination results in ultra long range at ultra low currents without concern for compliance approvals since modules such as the RFD21733 come with IC and FCC Approval and Certification for USA and have passed CE - ETSI emission testing for European requirements. The RFDP8 protocol adds several dB of range gain passively through it's advanced data recovery technique which pulls valid data out of a noisy environment adding effective gain which results in more range, delivering the net result, which is a very robust wireless system. All of this is built into the overhead of the RFDP8 protocol and RF Digital modules, so it's all done behind the scenes, allowing the user to focus on building their application and simply putting data into the radio device as a wireless pipe and easily receiving it on the other end. Electronic Serial Number Every RF Digital Module has its own 32-bit unique identifier (over 4 billion unique values), known as the Electronic Serial Number, or ESN. This value is assigned at the factory and cannot be changed by the user. The ESN is included in every packet that is transmitted, as part of the protocol overhead and is transparent to the user. The user does not ordinarily need to know what the ESN is. However, in certain cases it is helpful to know the serial number, and so a mechanism has been provided to read out the ESN. This method is documented in the UART section below. Free Applications Support * Email your application questions to support@rfdigital.com 25 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Network Mode The UART and the Receiver with logic output can be configured to accept data only from transmitters with which it has been associated, i.e. in its network. When in network mode, a module must "learn" the ESN of any module which it wishes to "hear." The LEARN signal (listed in the UART and receiver sections below) is usually an input, pulled to GND through an external resistor. When LEARN is driven high for at least 20ms and then allowed to return to GND, the module enters learning mode. While in learning mode, the LEARN signal is changed to an output and driven high. During this time, the module will learn the ESN of the first module that sends any data; the data will be discarded, the ESN of the transmitting module will be learned by the receiving module. The receiving module indicates that it has learned the ESN by toggling the LEARN output on and off quickly three times. After learning the transmitting modules ESN, or after 10 seconds pass, the module will exit learning mode by driving LEARN low and then changing it back to an input. The LEARN / STATUS pin is bidirectional, it is an input when in the LEARN state and an output when in the STATUS state, so you must drive it using a series resistor, we recommend you not use any value smaller 1k ohm to limit the amount of load current. There is an internal 47k pull down resistor on the Eval Boards ONLY, so if you use a value of 1k series resistor that will easily be enough to drive it high against the internal 47k pull down resistor. If you are not using an Eval Board and you are using the RF Module or RFDANT on its own, then you will need to add the 47k resistor yourself. Modules can learn up to 60 unique ESN's. ESN's cannot be deleted individually. The list of learned ESN's can be completely cleared by holding the LEARN signal high for at least 10 seconds and then releasing it. The module will erase its ESN list, and then drive the LEARN signal in a fast alternating high/low pattern for a few seconds to indicate that the ESN list is now empty. Once a module has learned the ESN of another module, it will accept any and all data from that module only and not any other modules. Up to 60 unique transmitters can be taught to one receiver. If a module is configured to any of the 3 Network modes and it has not learned any transmitters ESN, then it will not receive and therefore it will not output any data, until it learns at least one transmitter. This network feature can be used for peer-to-peer networks, point to multi-point networks, multi-point to multipoint networks. The association can be between two units for simple functions like opening a garage door or with many units to form complex networks with multiple nodes. Network Mode - LEARN Pin Application Circuit Here is an example of how to wire up the LEARN pin to use NETWORK MODE. This same example of the LEARN / STATUS pin connection applies for Mode 3, Mode 5 and Mode 7, the only thing that changes are the mode settings of course. This also applies to the RFDANT. An optional buffer for the LED output is recommended for production designs. Simply replace the LED with a FET to drive the LED for high drive currents. Free Applications Support * Email your application questions to support@rfdigital.com 26 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs If possible, use a 470 ohm resistor or larger, to allow for highest logic level on the LEARN input as possible, due to the resistive divider that forms when pressing the LEARN button. Reset Pin The RESET pin on all part numbers of RF Modules and RFDANT are active low and have an internal 3.3k ohm pull up resistor. So at 3V you will need to source at least 1mA to be able to pull it low to cause a reset. You can leave the reset pin open, you do not need to connect it. The only reason you would need to connect the reset pin is if you needed a way to reset the Module or RFDANT while in your circuit. A common cause to require this is if you wanted to change modes while powered up and therefore you need to assert a reset to cause the 3 mode pins to be re-read to change modes. Note keeping reset low all the time will draw about 1mA of current so if you plan on conserving current, you will want to bring it low only briefly to cause the reset and then let it go high again using its internal 3.3k ohm pull up. Layout Trace Routing and VIAs When doing your layout for the RFD21733 and RFD21735 avoid placing routs under the module if at all possible. Having traces under the module as long as they are fully covered by soldermask is typically fine, however placing VIAs under the module is not at all recommended since soldermask covering VIAs are typically not fully plugged and protected. Therefore, if there is any exposes soldermask under the module near an area were your board has an exposed via, there is a chance of a short. There is a slim chance of this ever happening, however if possible, make effort to avoid having VIAs under the Modules. Dual Placement Layouts for Modules and RFDANTs When ever possible, it is always recommended when you do your layout for the RFD21733 or RFD21735 to also place a footprint for one of the 11 pin RFDANT connectors. This gives you the option to do testing by not placing the RFD21733 or RFD21735 module on some of your PCBs and just placing the RFDANT 11 pin connector and plugging an RFDANT into your board. If your board does not have room for this, then of course, this is not in any way required, its just a recommendation to give you as much optional choices as possible. The RFDANT has about 4x the range of the RFD21733 so if you happen to need the extra range, it would always be available with a simple connector interface. Free Applications Support * Email your application questions to support@rfdigital.com 27 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Using CR2032 Batteries The CR2032 battery is very commonly used for power. The peak current draw for the Modules and RFDANTs are at about 17mA, and the background current is 2uA depending on the mode setting of course. Quite often capacitors are used in parallel with the CR2032 to help limit the amount of peak current the CR2032 is exposed to, so as to help it have a longer run time, since the CR2032 does not handle peak current very well over long durations of time. We recommend if you choose to place bypass capacitors tied to the CR2032 for this purpose, then do testing to compare if they really provide you a benefit or not. Quite often the leakage current of the capacitors are so high that they will have negative impact on the battery runtime rather then provide an advantage. At least if you have the room, place the pads, but before you place the caps for production, do testing to make sure they are really helping and not reducing your runtime. Mode Pins The mode pins are read just once, right after the Module or RFDANT comes out of reset or upon power up. If you change them and want them to be read again, then do a reset or power down and up again. Mode Select 0, Mode Select 1 and Modes Select 2, are three binary inputs which are to be terminated either high or low, they must not be left open at any time. Mode Select 2 and 1 are open and high Z inputs, so you can use a 47k resistor to pull them up or down, or you can connect directly to +V or GND. The Mode Select 0 has an internal 13k internal switched pull down. At power up or when the module comes out of reset, it will internally apply a 13k pull down on this pin just for an instant to check if it is high or not. After the mode selection test, which is done just once at start up lasts just microseconds. It is done like this to allow you to have an optional external switch to select between mode 0 and mode 1 without drawing extra current through an external pull down resistor which would statically be there all the time. If you will be directly connecting Mode Select 0 directly to +V or to GND that is fine. However if you will be adding a pull up, note you will be working against a 10k to 16k internal pull down at the time the pin is read, so take that into account since it will form a voltage divider and maybe not provide the expected level and cause the module to go into the wrong mode. So for Mode Select 0, we recommend using a 1k or smaller resistor for a pull up to make sure you get 90% +V for a logic high, we often use 220 ohms or just tie it directly to +V. If you will add a pull down, note that it will be in parallel with the internal 13k typical pull down for microseconds duration, after reset or power up. The Mode Select 0 can be left open, if you leave it open it will register as a LOW. However if you will know what mode you want in advance and will not be switching it, then we always recommend direct tie to +V or GND. Wake Up Time The Modules and RFDANTs wake up very fast. After a reset or after power on, 3mS later they are ready to transmit or receive. Output Drive Current - source and sink. The Module and RFDANT output pins and IO pins when in an output mode should not be expected to drive higher then 0.5mA each. This is done by design to keep as much high current sources from flowing through the Module or RFDANT. The amount of source and sink current available at the pins are actually quite a bit more, therefore they are seen in applications were they can directly drive LEDs with a series resistor of about 220 ohm and the LED still comes on at a couple milliamps, but we don't recommend that for production. For prototyping that is fine, since its quick and simple to hookup, but for production, we prefer to use a driver like a transistor or FET to Free Applications Support * Email your application questions to support@rfdigital.com 28 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs switch as much current as you like to drive your external devices such as high brightness LEDs. Note you must always use a series current limiting resistor when connecting an LED to a pin of course. The outputs are active high and therefore you can use an NPN transistor or an N channel FET to switch the ground lead of an LED easily. Power Saving When in mode 4,5,6 or 7 receive modes or in mode 2 or 3 Serial UART modes, you will draw 17mA since the receiver is 100% on all the time. If you need an internal duty cycle set, please contact support@rfdigital.com for any custom timing you require. However if you wish to have control over this yourself, since the RFDP8 Modules and RFDANTs are very fast waking (3mS), you can easily use a P-FET or PNP transistor and just simply remove power from the whole module and then draw ZERO current until you need the module. If you need help doing this, feel free to contact support@rfdigital.com anytime. The length of an RFDP8 Standard packet is about 12mS, so if you use a receiver duty cycle of 10%, that will be on for 30mS and off for 270mS, which will give you a latency of about 300mS and result in a 90% power savings, yielding a 1.7mA average current consumption. Doing a 1% duty cycle, would bring the average current consumption to 170uA and latency to 3 seconds. Custom configurations to fit your application are available, simply email support@rfdigital.com Pull Ups and Pull Downs for RF Modules, RFDANTs and Eval Boards. The Reset Pin has a 3.3k Pull Up, internal to the Module and RFDANT. The Factory Pin has a 3.3k Pull Down, internal to the Module and RFDANT. There are no internal pull ups or pull downs on any other pins except for "Mode Select 0", which has an internal 13k pull down temporarily applied when the device comes out of reset or after power up for about less then a millisecond. All other pull downs or pull ups must be applied by you, externally to the Module or RFDANT. If you are using the RFD Eval Boards (RFD21737, RFD21738, RFD21739, RFD21772, RFD21773) there are 47k pull downs on these Eval Boards, see the Eval Board Schematic for reference on Pull Downs and which Pins they on. Always send screen captures of your schematics and layouts to support@rfdigital.com for review. Table for Modules and RFDANTs. ONLY - RFD21733, RFD21735, RFD21742, RFD21743. RFDANT Module Pin # Pin # 2 13 1 10 5 16 6 7 8 9 10 11 4 3 17 3 4 5 6 7 14 15 Pin Label +V GND Mode Select 0 Mode Select 1 Mode Select 2 TX LED / Status / Learn IN1 / OUT1 / LOGIC IO IN2 / OUT2 / RXD IN3 / OUT3 / TXD RESET FACTORY Direction Input Input Input Input Input Input / Output Input / Output Input / Output Input / Output Input Input Pull Up or Pull Down +V Power Ground 13k ohm pull down for less then 1mS after reset or after power up. (Inside of Modules and RFDANTs) NONE NONE NONE NONE NONE NONE 3.3k pull up (Inside of Modules and RFDANTs) 3.3k pull down. (Inside of Modules and RFDANTs) Free Applications Support * Email your application questions to support@rfdigital.com 29 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Table for Eval Boards ONLY - RFD21737, RFD21738, RFD21739, RFD21772, RFD21773. EVAL Pin Label BOARD 1 GND 2 +V 3 ON 4 FACTORY 5 RESET 6 Mode Select 0 7 8 9 10 11 12 Mode Select 1 Mode Select 2 TX LED / Status / Learn IN1 / OUT1 / LOGIC IO IN2 / OUT2 / RXD IN3 / OUT3 / TXD Direction Pull Up or Pull Down Input Input Input Input Input Input Ground +V Power On input to on-board regulator. Tie to +V for board to run. 3.3k pull down. (Inside of Modules and RFDANTs) 3.3k pull up. (Inside of Modules and RFDANTs) 13k ohm pull down for about 1mS after reset or after power up. (Inside of Modules and RFDANTs) 47k pull down mounted on Eval Board. 47k pull down mounted on Eval Board. 47k pull down mounted on Eval Board. 47k pull down mounted on Eval Board. 47k pull down mounted on Eval Board. 47k pull down mounted on Eval Board. Input Input Input / Output Input / Output Input / Output Input / Output Free Schematic, Layout and Application Design Reviews For free Application, Schematic and Layout design reviews, send color screen captures or PDFs of your schematic and layout to support@rfdigital.com. RF Digital's Support and Application Engineers are ready to get your wireless application running today. Why spend lots of time reading volumes of data? Instead, simply send your application questions to support@rfdigital.com and receive direct, fast and personal answers focused on your specific project and needs. We look forward to hearing from you!!! MODES Mode 0 - Active RFID Transmitter RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 TX LED 9 5 IN1 Direction Function Input Input Input Input Input Output Input +V Power Ground Tie to GND Tie to GND Tie to GND Toggles high during transmission (1 blink every 2 seconds) Active high switch input #1 (optional) if not used, pull to GND. Active high switch input #2 (optional) if not used, pull to GND. Active high switch input #3 (optional) if not used, pull to GND. 10 6 IN2 Input 11 7 IN3 Input Free Applications Support * Email your application questions to support@rfdigital.com 30 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs The Active RFID Transmitter transmits a packet with its ESN every 2 seconds when the three inputs IN1, IN2, IN3 are all at a low logic level. If any of the three inputs go high, the module transmits the state of all three inputs every 15 ms, until all three inputs are low. The logic inputs should be tied low if they are not used in the end application. The module is active during transmit for 15ms, but remains in an ultra-low power mode for the rest of the 2 second interval. The average power over time is measured in microamps, such that a CR2032 battery should provide about 60 days of continuous use. If you wish to have longer usage you can contact support@rfdigital.com for intervals greater then 2 seconds, for example 20 seconds would estimate to about two years. During the 15ms transmission times the current consumption is about 15mA and during the roughly 2 seconds the current is about 2uA. The average current with a 2 second interval is about 120uA. The average current with a 30 second interval is about 10uA, and 60 second interval is about 6uA. Estimated runtime of many years can be achieved 30 second range due to the very low average current consumption. If you determine that you need a different period of transmission other than the 2 seconds, a shorter period or a longer period, then simply use Mode 1 shown below and use your own controller to pulse one of the 3 inputs at the desired period and it will perform exactly the same function as the RFID transmitter Mode 0. If longer periods of use are required, a larger battery can be used to allow it to run up to years of time without replacing the battery, or contact RF Digital to inquire about a custom time setting which will reduce the transmission interval thus reducing the average power consumption. The Mode 0 is effectively Mode 1, except, in addition to Mode 1 features, the module will internally cause input 1 to transmit on its own every 2 seconds. So Mode 0 can be looked at like it is a dual mode, it is functioning as an RFID transmitter as well at the same time it is available to use as a 3 input switch transmitter. If you use a Mode 2 or Mode 3 receiver with a Serial UART output you can easily detect the difference between transmissions which were caused by the RFID interval automatically or by the user pressing a button to cause IN1, IN2 or IN3 to go high which causes an immediate transmission, regardless of RFID interval. Note if you connect a series resistor and an LED to the LED output pin, that will draw extra current during the 15mS transmission time, it is good to have it there for testing, but take that into consideration when you go to production for your battery runtime. If you would like to use all or any one of the three switch inputs as button inputs, then simply place a pull down resistor around 47k or smaller on the inputs which you will be connecting to a pushbutton, so when you press the pushbutton the input will go high and when you release it the input will be pulled to ground by the 47k resistor. The Reset Pin has a 3.3k Pull Up, internal to the Module and RFDANT. The Factory Pin has a 3.3k Pull Down, internal to the Module and RFDANT. There are no internal pull ups or pull downs on any other pins except for "Mode Select 0", which has an internal 13k pull down temporarily applied when the device comes out of reset or after power up for about less then a millisecond. All other pull downs or pull ups must be applied by you, externally to the Module or RFDANT. If you are using the RFD Eval Boards (RFD21737, RFD21738, RFD21739, RFD21772, RFD21773) there are 47k pull downs on these Eval Boards, see the Eval Board Schematic for reference on Pull Downs and which Pins they on. Always send screen captures of your schematics and layouts to support@rfdigital.com for review. Free Applications Support * Email your application questions to support@rfdigital.com 31 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Mode 1 - Input Logic Transmitter RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 TX LED 9 5 IN1 10 6 IN2 11 7 IN3 Direction Function Input Input Input Input Input Output Input Input Input +V Power Ground Tie to +V Tie to GND Tie to GND Toggles high during transmission (1 blink every 15 milliseconds) Active high switch input #1 (optional) if not used, pull to GND. Active high switch input #2 (optional) if not used, pull to GND. Active high switch input #3 (optional) if not used, pull to GND. When all three switch inputs are low, the module does not transmit, but remains in an ultra-low-power state consuming only 2uA. When any of the three switch inputs go high, the module transmits the state of all three inputs. As long as any of the three inputs remain high, the module continues to transmit the state of all three inputs every 15ms, while transmitting it will draw about 15mA. You can also tie any of the three inputs to +V and then connect a switch between +V of the module and your supply, then once you apply +V to the module it will instantly transmit as fast as possible. This method can be used to consume zero current when not in use such as in the case of garage door openers or keyfobs and can be used for many years without consuming any current at all. The Reset Pin has a 3.3k Pull Up, internal to the Module and RFDANT. The Factory Pin has a 3.3k Pull Down, internal to the Module and RFDANT. There are no internal pull ups or pull downs on any other pins except for "Mode Select 0", which has an internal 13k pull down temporarily applied when the device comes out of reset or after power up for about less then a millisecond. All other pull downs or pull ups must be applied by you, externally to the Module or RFDANT. If you are using the RFD Eval Boards (RFD21737, RFD21738, RFD21739, RFD21772, RFD21773) there are 47k pull downs on these Eval Boards, see the Eval Board Schematic for reference on Pull Downs and which Pins they on. Always send screen captures of your schematics and layouts to support@rfdigital.com for review. Mode 2 - 9600 baud UART - Serial Transceiver RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 Not Used 9 5 Logic IO 10 11 6 7 RXD TXD Direction Function Input Input Input Input Input Output I/O +V Power Ground Tie to GND Tie to +V Tie to GND Do not connect, not used. Must be left open. Bidirectional switch logic I/O, if not used then must be pulled to ground through a 47k resistor. Also, must have series a resistor. RX Data Out, UART output of received data. 9600-8N1 TX Data In, UART input of data to transmit. 9600-8N1 Output Input Free Applications Support * Email your application questions to support@rfdigital.com 32 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Mode 3 - 9600 baud UART - Serial Transceiver (Network) RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 Learn / Status Direction Function Input Input Input Input Input I/O +V Power Ground Tie to +V Tie to +V Tie to GND Pulse high through a 220 ohm series resistor to enter learn mode. LED Learn Status Output. Must be pulled to ground through a 47k resistor and must have series a resistor. Bidirectional switch logic I/O, if not used then must be pulled to ground through a 47k resistor. Also, must have a series resistor. RX Data Out, UART output of received data. 9600-8N1 TX Data In, UART input of data to transmit. 9600-8N1 9 5 Logic IO I/O 10 11 6 7 RXD TXD Output Input IMPORTANT NOTE: The RXD pin is DATA OUTPUT. The data that the radio receives will come out of this pin. The TXD pin is DATA INPUT. Drive this pin with the data that you want the radio to send. This applies to both UART modes, Mode 2 and Mode 3. There are two conventions in industry when referring to TXD and RXD pins. The TXD stands for Transmit Data and the RXD stands for Receive Data. The conventions conflict when it comes to determining from which prospective are the labels referenced. For example, TXD in modes industry devices indicates data being transmitted out from that pin, indicating that pin is an output. The same goes for RXD, meaning data being transmitted into that pin from an outside device, indicating that pin is an input. That is correct for most noncommunication devices in industry. HOWEVER, this device, when functioning in its UART mode, functions as a communications device, "A Wireless Pipe", therefore the pin functions are reversed since they are from the radios prospective which is used in the RF communications field. In the RF communications field TXD means data to be transmitted, indicating the TXD pin is an input. The same goes for RXD from the radio prospective, which indicates that pin is an output, which is responsible for outputting the data the radio has received. Both references are right, its just a matter of knowing which one to use. If you are ever in doubt, about the direction of data signals, it is always recommended to place a 1k series resistor on the TXD pin and RXD pins, in between the radio and your device so there is never any chance of a possible conflict while you are prototyping causing device damage. Mode 2 and Mode 3 are both 9600 baud, half-duplex UART modes, suitable for connection to a microcontroller, or a level translator (such as a MAX202), then to an RS-232 port. RF transmission takes priority over RF reception, so that a module will not receive anything over the air if it is given a full-speed stream of serial data on its TXD input pin. Only when you stop sending data, there will be a chance for you to receive data. The UART is configured for 9600 baud, 8 data bits, 1 stop bit, and no parity. Because the module does not perform any parity checking on the data stream, it is possible to use 7 data bits with even or odd parity instead of 8 data bits with no parity. When in UART mode, the radio device remains in an active state with the radio enabled in receive mode. If you are only using the module as a receiver, you must terminate the TXD line with about a 47k pull up resistor to +V so you do not leave a floating input which may cause unintentional transmissions by the module detecting Free Applications Support * Email your application questions to support@rfdigital.com 33 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs anything other then a solid logic level on the TXD pin. Note you can also pull it to ground using a 47k resistor to terminate it if you require, but most applications will want to terminate by a pull up resistor if the pin is unused. The Eval boards pull it to ground using a 47K resistor, because the Eval boards are setup to work in 8 different modes, if you are just using UART only, you will want to pull it high rather then low. There is a general purpose IO line in mode 2 and mode 3 which is called LOGIC IO. This is a powerful feature which allows you to not only send serial data back and forth using the TXD and RXD, but in addition you can apply a high logic level to the LOGIC IO pin and it will start transmitting without the need for sending serial data into the TXD pin. Once it is transmitting, any mode 2 or mode 3 receiver's LOGIC IO pin will go high for the same duration of time. This allows you to send switch data between two transceivers as well as serial data. In some applications this is very useful since you can use this feature to have one master device turn on a slave device and wait for the slave device to be ready to communicate using the UART and then begin sending data to it rather than keeping it awake all the time. Bi-Directional LOGIC IO Operation - In Mode 2 and Mode 3. UART mode includes an additional bi-directional general-purpose IO line. The IO signal is generally an input, and should be pulled to GND with an appropriately sized resistor (for example 10k). If the IO signal is driven high, the module will transmit this information, and any UART which receives the data will turn its IO signal into an output and drive it high. This will continue until 20ms pass without receiving any new data, or until the module receives a packet which indicates that the IO signal should be driven low and turned back to an input. The state of the IO signal does not require any extra data in the radio stream, and so is "free" in the packet overhead. When the module is driving its IO signal high, it will periodically change the pin to an input and check to see if it remains high, before changing it back to an output. This causes a periodic dip in the signal, 1ms every 12-16ms, and so any circuitry which relies on a steady-state output from the IO signal should include conditioning (for example a retriggerable one-shot with a hold time of 2ms) to avoid adverse effects. Note even if there is no data inputted into the TXD line and the TXD line is pulled high or low through a resistor and kept at a steady state, simply applying a high on the LOGIC IO pin will cause that radio to start transmitting and stay transmitting as long as the LOGIC IO pin is kept high. This is a huge advantage if you want to use it to reset a remote device for example or use it to turn on an external device located at the receiving radio, all without the need of doing decoding of data on the receiving end to process the command signal. Also another very powerful feature of this function is to use it to pass command signals to the receiving radio without needing to use escape codes hidden within the data stream which can always cause problems, this LOGIC IO feature with the RFDP8 protocol completely resolves this long time industry problem with UART escape codes with wireless devices. IMPORTANT NOTE - LOGIC IO Pin (This pin is BI-DIRECTIONAL) The LOGIC IO pin MUST be terminated when in mode 2 or 3, (pulled to ground with a 47k resistor) or it will float and cause the transmitter unintentionally. All inputs must be terminated properly and this one is no exception. If you do not plan on using it, tie it to ground using any resistor between 10k to 47k. Note this is a BIDIRECTIONAL pin so do not directly connect to an output or to ground, you must use a pull down resistor. Also, when in use with a microcontroller pin you should consider using a series 1k resistor as well between the LOGIC IO pin and your controller pin since that will prevent any possible conflicts that might happen if you chose to drive the pin when it was an output by mistake, which can be a very common occurrence. In addition, if you plan on connecting the LOGIC-IO Pin to a pushbutton switch, then you must have a series current limiting resistor in the order of about 1k, so when you press the button and drive the pin high, you can never have more then about a 1mA load on the pin just in case it happened to turn into an output at anytime since it is bi-directional. Of course, the 47k pull down would still be required as well to make sure the input is not floating. Free Applications Support * Email your application questions to support@rfdigital.com 34 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs End-to-End Latency The RFDP8 firmware buffers data inputted into its TXD pin of its UART into packets, which are transmitted over the air. The firmware transmits a packet when it has buffered 12 bytes of data, or 15ms after receiving a byte of data, which ever comes first. On the receiving end, data will be outputted on the RXD pin of the UART at line speed, with no pauses between the bytes (other than the UART start and stop bits). The RFDP8 protocol can run at full speed, line-rate, meaning without any spaces at all. Of course you can space out your bytes at any pace you like, however as many bytes as you input into the TXD pin during each 15mS period will be collected into one packet and sent at one time to the receiving radio and outputted in one burst at full line-rate. The buffering and latency may cause problems with certain microcontrollers that can not tolerate serial data into their UART in a constant stream at 9600-8N1. One possible solution is to add a 16ms delay on the transmitting side which will cause each byte to be sent in its own packet by the module and therefore on the receiving end the bytes will be outputted at a pace of one byte every 16ms which will help your controller of choice handle the fast UART data. As an example, consider a scenario where one system is sending a byte of data every 8ms. When module 1 receives the 1st byte on its UART, the 15ms timer begins. The 2nd byte arrives before 15ms elapses, and so the first two bytes are sent in a single packet over the air to Module 2. Module 2 will transmit the bytes on its UART with no delay between them. Module 1 receives the third byte on its UART, and re-starts the 15ms timer. As with the 2nd byte, the 4th byte arrives before 15ms elapses, and so the 3rd and 4th bytes are also sent in a single packet over the air, as illustrated in the following timing diagram. Wake up time after power up and saving power. After the module is powered on, 3mS later it is ready to receive or transmit. So if you want to consume zero current when you don't need to use the radio, you can simply use an external FET or PNP transistor and turn the device fully off when you don't need it and only turn it on when you want to send or receive data. If you require any of this to be done automatically and internally to the Module or RFDANT, contact support@rfdigital.com ESN Read-back In certain applications, it is helpful to know the ESN of a module. There is a provision in both UART modes to read back the ESN when the module comes out of reset. ESN read-back is not available in any of the other modes. Free Applications Support * Email your application questions to support@rfdigital.com 35 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs You will need to use the RESET pin, this pin normally is not connected for nearly all applications except for reading back the ESN or possibly using it to have the mode pins re-read and change modes without power cycling. The reset signal does not have to be used, instead of using reset you can use power the module off and then back on. The reset is a cleaner way of doing it. If you are using the RFD21737, RFD21738, RFD21739, RFD21772, RFD21773 eval boards, the reset signal is available on pin 5 of the 12 pin connector. Internal to the RFD21733 / RFD21735, RFD21742, RFD21743 there is a 3.3K pull up resistor on the reset signal, so when you are not using it, you can just leave it open. To activate ESN read-back: 1. Place the module in a reset state by holding the /RESET signal low. 2. Hold the LEARN signal high. (On the Eval board you can press and hold the LEARN button.) 3. Release the /RESET signal. 4. Wait 250ms. If the LEARN signal goes low at any time during this 250ms interval, the module immediately exits ESN read-back mode. 5. Release the LEARN signal. 6. Send the string "READ ESN" (all capitals, one space between the two words) at 9600-8N1 into the module on the TXD Input signal. If this string is not received within 1 second, the module exits ESN readback mode. The module will respond with the ESN and a firmware identifier on the RXD Output signal at 9600-8N1, and then exit ESN read-back mode. An example of the output is: 314CE686:RFDP8 v1.2 11/18/08 08:45:16$ The ESN is 8 characters, representing a 32-bit number in hexadecimal format. A colon separates the ESN from the Firmware ID. The Firmware ID is 32 bytes long. The output is terminated with a carriage return/line feed pair. When the module exits ESN read-back mode, or if the LEARN signal is not high when the module exists reset, the module will enter regular operation in Mode 2 or 3, according to the mode select signals. IMPORTANT NOTE - Mode 3 and ESN Read Back If at all possible, do your ESN read-backs in Mode 2 and not Mode 3. The reason for this is that in Mode 3, if you happen to do this manually (by hand using an Eval board), once the radio outputs the ESN string, it will enter normal usage mode meaning it will directly enter into LEARN mode when you release the LEARN pin and then spend 10 seconds waiting for a packet to be received so it can learn its ESN. You can prevent this by using a controller to time this activity, or you can simply do it in Mode 2 and not have the concern. If you have any questions, always feel free to email support@rfdigital.com. Watch a video demonstrating how to do the ESN Read Back using HyperTerminal and an Eval Board: http://www.rfdigital.com/?targetpage=item&filterpn=RFD76021 Free Applications Support * Email your application questions to support@rfdigital.com 36 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Mode 4 - Switch Receiver with Logic Output (500ms hang-time) RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 Not Used 9 5 OUT1 10 6 OUT2 11 7 OUT3 Direction Function Input Input Input Input Input Output Output Output Output +V Power Ground Tie to GND Tie to GND Tie to +V Leave open, not used. Active high switch output #1, 500 millisecond hang-time. Active high switch output #2, 500 millisecond hang-time. Active high switch output #3, 500 millisecond hang-time. Mode 5 - Switch Receiver with Logic Output (500ms hang-time) (Network) RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 Learn / Status 9 10 11 5 6 7 OUT1 OUT2 OUT3 Direction Function Input Input Input Input Input I/O +V Power Ground Tie to +V Tie to GND Tie to +V Pulse high through a 220 ohm series resistor to enter learn mode. LED Learn Status Output. Must be pulled to ground through a 47k resistor and must have series a resistor. Active high switch output #1, 500 millisecond hang-time. Active high switch output #2, 500 millisecond hang-time. Active high switch output #3, 500 millisecond hang-time. Output Output Output Mode 6 - Switch Receiver with Logic Output (20ms hang-time) RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 Not Used 9 5 OUT1 10 6 OUT2 11 7 OUT3 Direction Function Input Input Input Input Input Output Output Output Output +V Power Ground Tie to GND Tie to +V Tie to +V Leave open, not used. Active high switch output #1, 20 millisecond hang-time. Active high switch output #2, 20 millisecond hang-time. Active high switch output #3, 20 millisecond hang-time. Free Applications Support * Email your application questions to support@rfdigital.com 37 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Mode 7 - Switch Receiver with Logic Output (20ms hang-time) (Network) RFDANT Module Pin Label Pin # Pin # 2 13 +V 1 10 GND 5 16 Mode Select 0 6 17 Mode Select 1 7 3 Mode Select 2 8 4 Learn / Status 9 10 11 5 6 7 OUT1 OUT2 OUT3 Direction Function Input Input Input Input Input I/O +V Power Ground Tie to +V Tie to +V Tie to +V Pulse high through a 220 ohm series resistor to enter learn mode. LED Learn Status Output. Must be pulled to ground through a 47k resistor and must have series a resistor. Active high switch output #1, 20 millisecond hang-time. Active high switch output #2, 20 millisecond hang-time. Active high switch output #3, 20 millisecond hang-time. Output Output Output Fast Switch Latency The RF Modules and RFDANTs with their patent pending RFDP8 interference tolerant protocol have fast response times. When using a Mode 0 or 1 transmitter and a Mode 4, 5, 6 or 7 receiver, from the time the transmitter switch input goes high, the receiver output will go high as fast as 5 milliseconds later. It might take as long as 12mS, but most of the time it is closer to the 5mS time frame. In Mode 4, Mode 5, Mode 6 and Mode 7, the Module or RFDANT is always in switch receiving mode. The receiver drives its outputs to match the values received in a packet from a transmitter. This allows up to 8 possible (23) combinations on the receiver's outputs. The term Hang-Time means the period the output will stay high after it has been turned on. It will stay on for the duration of the hang time, waiting on another packet to be received, if no other packet is received it will go low after the hang-time period. If a packet is received within the hang-time period it will continue to stay high again for that period of the hang-time setting (either 20mS or 500mS). If repetitive packages are received within the hangtime window then the output which was high, will continue to stay high as long as that same input is kept high at the transmitting radio or Serial transmitter which sent the packet. Hang time is a trade-off between off-time-latency and resiliency to packet loss. With all RF systems sometimes a packet will be lost, especially as the distance between the transmitter and the receiver grows. If an output is connected to a relay driver, packet loss will result in chattering on the relay, which will not have good results. The 500ms hang time is perfect for applications like a keyless entry system or a garage door opener. For faster switching to the "all off" state, the 20ms hang time is preferred. Since a transmitter sends new data every 15ms, the time delay to turn off all outputs is only 5ms more than to update the outputs to a different state where at least one of them is still driven high. Free Applications Support * Email your application questions to support@rfdigital.com 38 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs The following timing diagrams show the operation of a logic transmitter and a logic receiver with the different hang time options. In the first diagram, the logic transmitter's inputs are all asserted, and then sequentially de-asserted. There is a small delay between the transmitter input going high and the corresponding output on the receiver going high, due to the time required to transmit over the air. Note that when the last input on the transmitter is de-asserted, there is a 500ms delay before the receiver deasserts its last output. The second diagram shows the same operation at the transmitter, but with the receiver configured with a 20ms hang time. Note that shortly after the last input is de-asserted, the receiver updates its output state to turn off all outputs. Communication between UART and Switch Logic Receiver/Transmitter The Logic Receiver and Transmitter modes are able to communicate with a module operating in one of the UART modes, which opens up a wide range of possible applications involving PC's or embedded systems with serial communications capability. Logic Transmitter to UART A Logic Transmitter (whether RFID or not) sends the state of its inputs as a single byte of data, followed by its ESN as four bytes. A Mode 2 or Mode 3, Module or RFDANT in Serial UART can receive this packet and output it as a binary stream to a PC serial port or an embedded microcontroller. The format of the data is: Free Applications Support * Email your application questions to support@rfdigital.com 39 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified Byte 1 Bit 7 2 3 4 5 Bit 6 Input 3 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com Bit 5 Input 2 Bit 4 Bit 3 Input 1/ RFID ESN Byte 1 ESN Byte 2 ESN Byte 3 ESN Byte 4 Bit 2 Bit 1 RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Bit 0 RFID In the first byte, bits 6 through 4 carry the state of the logic inputs, with a `1' indicating the logic input on the transmitter is high, and a `0' indicating it is low. An RFID Transmitter will set both bits 0 and 4 to indicate that it is a periodic transmission from an RFID Transmitter, and is set to `1' if this is the case. For example, if an RFID Transmitter with ESN 314CE686 sent a packet on its 2-second interval, a UART would receive the bytes 11 31 4C E6 86 in binary format. If input #1 on that same RFID transmitter were pulled high, the UART would receive the bytes 10 31 4C E6 86 in binary format; since bit 0 is clear, the receiver can tell that this was not a periodic transmission. Most ESN's will contain at least one unprintable character, and so this data will not be suitable for displaying directly in a terminal package (such as HyperTerminal), but a PC-based program or an embedded system (such as the BASIC Stamp) can collect the data and display it in a more friendly fashion. There is a very useful tool on the web called RealTerm, it is a HyperTerminal like software which can be put into binary-mode and with it you can easily view the individual bytes sent from a serial transmitter to a UART receiver. The ESN which the UART receives is the same one that is in the packet header. If the UART is in Network Mode, and has not learned the ESN, it will never receive the packet, and there will be no output on the serial port. Serial UART to Logic Receiver A UART can also send data to a logic receiver, which will decode the data and assert its outputs as though it received a packet from a logic transmitter. The data format is very similar to the one described in the previous section. The differences matter only when the receiver is in Network Mode. The UART must follow a packet with at least 15ms of no data so that all bytes as described below are sent as a single packet. Note that a UART can send a single zero byte - all bits clear - to force a receiver to turn off its outputs immediately, regardless of hang time. Format 1: Byte 1 Bit 7 Bit 6 Bit 5 Bit 4 Output 3 Output 2 Output 1 Bit 3 Bit 2 Bit 1 Bit 0 When the receiver is not in Network Mode, the receiver will accept any packet it receives, and so this is the preferred format. Free Applications Support * Email your application questions to support@rfdigital.com 40 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs A receiver in Network Mode will use the UART's ESN from the packet header to determine if it should accept the packet. This allows one UART to send the same data to multiple receivers, provided that each receiver has learned the UART's ESN. Format 2: Byte 1 2 3 4 5 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Output 3 Output 2 Output 1 ESN Byte 1 ESN Byte 2 ESN Byte 3 ESN Byte 4 Bit 2 Bit 1 Bit 0 To allow individual addressing of receivers in Network Mode, the UART can send a particular receiver's ESN after the byte for the logic state. In this case, the receiver will only accept the packet if the ESN in the data portion matches the receiver's own ESN. If the receiver is actively learning ESN's, it will learn only the ESN from the packet header; the ESN in the data portion will not be learned. Free Schematic, Layout and Application Design Reviews For free Application, Schematic and Layout design reviews, send color screen captures or PDFs of your schematic and layout to support@rfdigital.com. RF Digital's Support and Application Engineers are ready to get your wireless application running today. Why spend lots of time reading volumes of data? Instead, simply send your application questions to support@rfdigital.com and receive direct, fast and personal answers focused on your specific project and needs. We look forward to hearing from you!!! Free Applications Support * Email your application questions to support@rfdigital.com 41 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Electrical Characteristics Operating Conditions Notes RFDP8 M0 Pin ** Parameter VDD Supply voltage Supply Rise Time Operating Temperature Input High Voltage Input Low Voltage Output High Voltage (@ 0.5mA) Output Low Voltage (@ 0.5mA) Internal CPU Controlled Pull-Ups Internal CPU Controlled Pull-Downs Power Up Time - Ready to Transmit Power Up Time - Ready to Receive After Reset - Ready to Transmit After Reset - Ready to Receive Minimum 1.9V 1uS -40C VDD x 0.7 VSS VDD - 0.7V VSS 11k ohm 11k ohm Typical 3.0V 13k ohm 13k ohm 3mS 3mS 3mS 3mS Maximum 3.6V 50mS +85C VDD VDD x 0.3 VDD 0.3V 16k ohm 16k ohm ** Note (RFDP8 M0 Pin) The RFDP8 Modules and RFDANTs have 3 pins used to set the mode the device will go into after reset or power up. These pins are called M2, M1 and M0. M0 pin is the low order pin. At power up or when the module comes out of reset, it will internally apply a 13k pull down on this pin just for an instant to check if it is high or not. After the mode selection test, which is done just once at start up lasts just microseconds. This is done like this to allow you to have an optional external switch to select between mode 0 and mode 1 without drawing extra current through an external pull down resistor which would statically be there all the time. Power Consumption Conditions: VDD = 3.0V, TA = +25C Logic Transmitter Parameter Ultra-low power mode - background - Switch Logic Transmitter Minimum Typical 2uA Maximum Minimum Typical 17mA 14mA Maximum UART or Switch Logic Transmitter / Receiver Parameter Listening - Receiving Transmitting Free Applications Support * Email your application questions to support@rfdigital.com 42 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Overall Dimensions * Top View Overall Dimensions * Side View Free Applications Support * Email your application questions to support@rfdigital.com 43 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs PCB Layout Free Applications Support * Email your application questions to support@rfdigital.com 44 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs IC Only applies to modules which show "IC: 6992A-24" on the shield. Modules which do not show IC: 6992A-24 on the shield are NOT certified for use in Canada. RFD21733 modules with date codes before "1120" (20th week of 2011) are not Industry Canada approved. IC NOTICE Relating to Model Number R24 (RFD Stock Code: RFD21733) The unit should have a permanently attached label in a conspicuous location with the following statement: Contains IC: 6992A-24 NOTES: 1. Industry Canada does not specify the size of the label or the lettering thereon. The only requirement is that the text be legible. Free Applications Support * Email your application questions to support@rfdigital.com 45 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs INDUSTRY CANADA INFORMATION Relating to Model Number R24 (RFD Stock Code: RFD21733) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Conformement a la reglementation d'Industrie Canada, le present emetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inferieur) approuve pour l'emetteur par Industrie Canada. Dans le but de reduire les risques de brouillage radioelectrique a l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnee equivalente (p.i.r.e.) ne depasse pas l'intensite necessaire a l'etablissement d'une communication satisfaisante. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Free Applications Support * Email your application questions to support@rfdigital.com 46 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs FCC NOTICE Relating to Model Number R24 (RFD Stock Code: RFD21733) The unit should have a permanently attached label in a conspicuous location with the following statement: Contains FCC ID: UYI24 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTES: 1. The FCC does not specify the size of the label or the lettering thereon. The only requirement is that the text be legible. 2. If the entire label can not be placed on the unit due to space constraint, only FCC ID may be displayed on the unit. In such cases, the compliance statement will have to be included in the "user's manual". NOTE: Device must be smaller than a man's palm. ** If the unit also interfaces with phone line, it requires additional information on the label - refer to part 68 information ** Free Applications Support * Email your application questions to support@rfdigital.com 47 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs SAMPLE FCC STATEMENT TO BE INCLUDED IN USER'S MANUAL Relating to Model Number R24 (RFD Stock Code: RFD21733) INSTRUCTION TO THE USER (if device DOES NOT contain a digital device) The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. Free Applications Support * Email your application questions to support@rfdigital.com 48 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs FCC NOTICE Relating to Model Number RFDANT (RFD Stock Code: RFD21743) LABELING REQUIREMENT FOR USA FCC CERTIFICATION This device has a modular approval from the FCC. You must place the following label outside, on your product in an obvious location. Permanently attached label in a conspicuous location with the following statement: This device contains FCC ID: UYI-RFDANT RF module that complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTES: 1. The FCC does not specify the size of the label or the lettering thereon. The only requirement is that the text be legible. 2. If the entire label can not be placed on the unit due to space constraint (e.g. Pacemaker), only "contains an FCC ID: UYI-RFDANT" may be displayed on the unit. In such cases, the compliance statement will have to be included in the "instruction to the user." ******* It is the users responsibility to determine if their device requires additional approvals ******* Free Applications Support * Email your application questions to support@rfdigital.com 49 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs SAMPLE FCC STATEMENT TO BE INCLUDED IN USER'S MANUAL Relating to Model Number RFDANT (RFD Stock Code: RFD21743) INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. Free Applications Support * Email your application questions to support@rfdigital.com 50 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RoHS Declaration Of Conformity RF Digital declares that part numbers * RFD21731 * RFD21732 * RFD21733 * RFD21734 * RFD21735 * RFD21736 * RFD21737 * RFD21738 * RFD21739 * RFD21741 * RFD21742 * RFD21743 * RFD21764 * RFD21772 * RFD21773 are manufactured with RoHS materials. Free Applications Support * Email your application questions to support@rfdigital.com 51 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs DECLARATION OF CONFORMITY June 29, 2010 RF Digital declares that part numbers * RFD21731 * RFD21732 * RFD21733 * RFD21734 * RFD21735 * RFD21741 * RFD21742 * RFD21743 comply with ETSI EN 300 440-2 power requirements as called out in the R&TTE V1.2.1 Directive Technical documents for the above mentioned part numbers are held at RF Digital Corporation 13715 Alton Pkwy. Irvine, CA 92618 Free Applications Support * Email your application questions to support@rfdigital.com 52 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Washing The RFD21733 and RFD21735 are NOT washable. Use no-clean flux, leaded or lead-free. If you attempt to wash the modules, water will enter beneath (inside) the RF shield and get trapped, which may cause device failure or damage once powered on. There is no way to make sure all water has been removed before powering the module so do NOT wash the modules. Potting, Encapsulation and Conformal Coating Do NOT pot or conformal coat the RFD21733 or RFD21735. If you plan on encapsulating the RFD21733 or RFD21735 in a potting compound or conformal coating, you must assure that the compound in liquid or solid form does not enter under the shield where there are sensitive RF components. Some of the capacitive values are as low as half a picofarad and sensitive to contacting materials such as potting compounds. There are potting compounds and conformal coatings which have very good dielectric constants and are suitable for 2.4 GHz potting applications, however, when you apply any of these, they were accounted for in the circuit design and might reduce performance of the device or all together cause it not to function. Applying any compound, conformal coating or potting directly to the module voids any and all warranty and support service. If your application requires 100% sealing of the module, there is a way to do this very successfully without impacting the module performance. Simply place the module on your PCB. Place a plastic cover over the module (like a hat), make the cover large enough to cover the whole module. Apply glue around the bottom perimeter of the cover where it sits on the PCB. This allows the module to function in free airspace while there is a complete seal around it. This information is only for reference and you should do your own testing with your application to find the best suitable fit for your own design. Reflow Profile Use standard lead-free or leaded reflow profile for the RFD21733 and RFD21735. Your CM (Contract Manufacturer) should profile this module along with your PCB and all other parts on it through their reflow oven to properly set a profile suitable for all the parts on the board combined. USE CAUTION: If you are building a double-sided placement board, place this device last so it will not be subjected to being reflowed upside-down. As with building any RF devices, you should always build a small quantity through your production process, test and verify, then increase your quantities to make sure the process is not harmful to the performance of your RF system. This is true with any RF system, including use of these modules. Free Applications Support * Email your application questions to support@rfdigital.com 53 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21733 / RFD21735 Tray Packaging Free Applications Support * Email your application questions to support@rfdigital.com 54 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21733 / RFD21735 Tray Packaging Free Applications Support * Email your application questions to support@rfdigital.com 55 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21733 / RFD21735 Tray Packaging Free Applications Support * Email your application questions to support@rfdigital.com 56 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Surface Mounted RF Module Layout Examples For Part Numbers RFD21731, RFD21732, RFD21733, RFD21734, RFD21735 Free Schematic, Layout and Application Design Reviews For free Application, Schematic and Layout design reviews, send color screen captures or PDFs of your schematic and layout to support@rfdigital.com. RF Digital's Support and Application Engineers are ready to get your wireless application running today. Why spend lots of time reading volumes of data? Instead, simply send your application questions to support@rfdigital.com and receive direct, fast and personal answers focused on your specific project and needs. We look forward to hearing from you!!! RFD21733 FCC / IC Approved Built-In Antenna For use with External Antenna 21731 / 21732 / 21733 / 21734 / 21735 RFD21735 / RFD21734 RFD21731 / RFD21732 / RFD21733 Legend Please use the legend below to identify the colors, objects and their meanings in this document. Free Applications Support * Email your application questions to support@rfdigital.com 57 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 Layout Example Pinout This Layout Examples document only references pins that are common to all RFD21731,2,3,4,5 modules and matter to the layout, which are ground and external antenna connections where applicable. To keep the file size of this document small, some of the larger images are outputted in lower resolutions, for full details on pinouts refer to the data sheet for the appropriate part number, which can all be found at http://www.rfdigital.com. Pins labels 3,4,5,6,7,14,15,16,17 change based on which part number module is being used, however that does not matter for this document, because the same layout rules apply to the RFD21731, RFD21732, RFD21733, RFD21734 and RFD21735 modules. Majority of this document addresses the RFD21731, RFD21732, RFD21733 and the end of this document addresses the RFD21734 and RFD21735. If you have any questions, feel free to contact RF Digital Support anytime, we're always here to help you! Free Applications Support * Email your application questions to support@rfdigital.com 58 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 Layout Examples The following layout examples are for the RFD21731, RFD21732 and RFD21733 module which all have a built-in chip antenna. Later in this document there are examples for the RFD21734 and RFD21735 modules, which are for use with external antennas. RFD21731, RFD21732, RFD21733 Antenna Pattern This is a typical antenna pattern, however does vary based on many factors including surrounding components and ground planes. It is only provided as a reference. The one inch copper plane shown helps maintain the balanced antenna pattern and when possible should be used, if not possible, its not required. Free Applications Support * Email your application questions to support@rfdigital.com 59 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 Keep Out Area - Example 1 When placing the module info a plastic enclosure, it is highly recommended that you locate the module in the corner of the enclosure / PCB so it will be as far away from your other components on the PCB and as close to free airspace as possible. In addition, you want to locate the module in a position in your product where it will have as much free airspace as possible near the antenna when in use. For example if it will be placed against a wall, it is preferred to locate the module so it will be in a location in your product where it will be on the side of the product where it will be further away from the wall, rather then directly next to it, so the RF signal can have as much free airspace to give you the best range performance possible. (Note: If you plan on using a metal enclosure, you can not locate the module inside of the enclosure or it will have very limited range, for metal enclosures we recommend the RFD21743 which is specifically suited for that.) The electrical ground connection to the module is to be made with a thin trace so the one inch ground plane off to the side can be effective. RF Signals in this area. If you place anything such as components, wires, metal parts of any type in this area, it will block the RF signals and drastically limit your range. Leave this area open. Free Applications Support * Email your application questions to support@rfdigital.com 60 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 2 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Also the signal connections to the module can be made on either layer. The electrical ground connection to the module is to be made with a thin trace so the one inch ground plane off to the side can be effective. RF Signals in this area. If you place anything such as components, wires, metal parts of any type in this area, it will block the RF signals and drastically limit your range. Leave this area open. Free Applications Support * Email your application questions to support@rfdigital.com 61 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 3 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. RF Signals in this area. If you place anything such as components, wires, metal parts of any type in this area, it will block the RF signals and drastically limit your range. Leave this area open. Free Applications Support * Email your application questions to support@rfdigital.com 62 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 4 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Free Applications Support * Email your application questions to support@rfdigital.com 63 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 5 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Free Applications Support * Email your application questions to support@rfdigital.com 64 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 6 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Free Applications Support * Email your application questions to support@rfdigital.com 65 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 7 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Solid blue areas are solder side ground plane which can be used for user electronics as well as the module. These are all optional configurations and only for reference. Free Applications Support * Email your application questions to support@rfdigital.com 66 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 8 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Solid blue areas are solder side ground plane which can be used for user electronics as well as the module. These are all optional configurations and only for reference. The two left examples are preferred, but the two right ones will work as well, but will not have as good of an antenna pattern. Free Applications Support * Email your application questions to support@rfdigital.com 67 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 9 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Solid blue areas are solder side ground plane which can be used for user electronics as well as the module. These are all optional configurations and only for reference. The two left examples are preferred, but the two right ones will work as well, but will not have as good of an antenna pattern. Free Applications Support * Email your application questions to support@rfdigital.com 68 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 10 The gray area shows where to keep free from copper and components. The one-inch length copper area is optional, however does improve the range if you can add it. Parts can be placed all over the rest of the board, however if possible keep about a half-inch distance from the one inch length ground area to the right of the module, again, only if possible. Solid blue areas are solder side ground plane which can be used for user electronics as well as the module. These are all optional configurations and only for reference. The space in the ground plane helps provide some RF discontinuity for the module to have he best antenna pattern possible in this configuration, the optimal space to have is greater then 1.2 inches, but some space is better then no space. Free Applications Support * Email your application questions to support@rfdigital.com 69 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 11 The gray area shows where to keep free from copper and components. These shown are not good layout locations for the module since they take up most of your board area, it is best to locate the module similar to the examples shown in other areas of this document where you have more board space for your parts. These examples are shown as what NOT to do. If you place parts in the gray area, it will result in very bad range performance. Free Applications Support * Email your application questions to support@rfdigital.com 70 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 12 The gray area shows where to keep free from copper and components. These shown are not good layout locations for the module since they take up most of your board area, it is best to locate the module similar to the examples shown in other areas of this document where you have more board space for your parts. These examples are shown as what NOT to do. If you place parts in the gray area, it will result in very bad range performance. Free Applications Support * Email your application questions to support@rfdigital.com 71 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 13 The gray area shows where to keep free from copper and components. These are multi-module configurations. Typical layouts for diversity applications where you will use multiple receivers, transmitters or transceivers all on the same board to limit multipath impacts and increase effective communication range or provide a very solid coverage area with limited dead-zones. The distances shown are not optimal, however just provided as reference. Free Applications Support * Email your application questions to support@rfdigital.com 72 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21731, RFD21732, RFD21733 - Layout Examples 14 The gray area shows where to keep free from copper and components. These are multi-module configurations. Typical layouts for diversity applications where you will use multiple receivers, transmitters or transceivers all on the same board to limit multipath impacts and increase effective communication range or provide a very solid coverage area with limited dead-zones. The distances shown are not optimal, however just provided as reference. Free Applications Support * Email your application questions to support@rfdigital.com 73 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs RFD21734 and RFD21735 - Layout Examples 15 The gray area shows where to keep free from copper and components. The RFD21734 and RFD21735 require the use of an external antenna and therefore the most common connector used for this is an SMA and the examples below show a typical SMA connector footprint interface. PCB thickness is 0.031 inch to 0.062 inch, double sided. The blue color shows ground plane under the module on the solder side of the board. If you place ground plane or any traces under the gray area marked no-copper, then you will not have the option to use the RFD21731 / RFD21732 / RFD21733 which are the on-board chip antenna versions of the RFD21734 / RFD21735. So it is your choice if you choose to flood copper under that area or not. There is no benefit to flood copper in that area. If you choose to make a dual-mode layout to handle both module options, with chip antenna or without (which is what we recommend), then also advise with the layout configurations above for proper application. We highly recommend that you look at the RFD21743 and RFD21742 before starting a design with the RFD21734 or RFD21735. The RFD21742 and RFD21743 are RF Digital's Patent Pending RFDANTs, which are complete RF Modules setup for external use and already in an antenna form factor allowing you to simply plug it into any product instantly, without needing any layouts, RF connectors or coax cables. They offer exceptional range, about 4x that of the RFD21733. Save time, money and no need for additional compliance approvals since the RFD21743 is FCC Approved and Certified Free Applications Support * Email your application questions to support@rfdigital.com 74 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs Important Notice RF Digital reserves the right to make corrections, modifications, and/or improvements to the product and/or its specifications at any time without notice. RF Digital assumes no liability for the user's product and/or applications. RF Digital products are not authorized for use in safety-critical applications, including but not limited to life-support applications. RF Digital assumes no liability for parts or their application beyond replacement or refunding the original purchase price. All trademarks and trade names belong to their respective owners. Information provided in this document is for reference only. The user must conduct testing and prototyping on their own for their own application. This document only provides an example of a possible use for the parts shown in this design and requires actual testing to confirm its accuracy or validity or proper application. There is NO suggestion that the devices shown in this document should be used for the implied application. There is no guarantee or warranty of suitability for any specific application. The information disclosed in this document is AS-IS. By using any information contained in this document you are assuming all risks and liability associated therewith. RF Digital reserves the right to make corrections, modifications, changes and/or improvements to specifications or details at any time without notice or obligation. RF Digital assumes no liability for the user's product and/or applications. RF Digital products are not authorized for use in safety-critical applications, including but not limited to life-support applications. RF Digital assumes no liability for parts or their application beyond replacement or refunding the original purchase price paid to RF Digital. Limited Product Warranty RF Digital warrants that RF Devices manufactured by RF Digital are free from defects in material and workmanship, for Ninty (90) Days from date of delivery. RF Devices covered by this warranty and returned to RF Digital within the Ninety Day Warranty Period will be eligible for replacement, repair, or credit, limited to the amount RF Digital was paid for the RF Device. To obtain a remedy under this Warranty, the following conditions must be met: (1) Customer must notify RF Digital in writing promptly on discovery of the deficiency with reasonable detail within the Warranty Period; (2) Customer must return the RF Devices to RF Digital promptly upon receipt of an RMA from RF Digital, at Customer's risk and expense; and (3) RF Digital confirms the claimed Free Applications Support * Email your application questions to support@rfdigital.com 75 (c) Copyright, RF Digital 7/10/2011 1:40 AM Patents Pending RoHS CE * ESTI RFD21733 * FCC * IC RFD21743 * FCC Approved & Certified 13715 Alton Pkwy * Irvine * CA * 92618 Tel: 949.610.0008 * www.RFdigital.com Fast Answers: support@rfdigital.com RFDP8 RFDP8 RF Module RFD21733 RFD21735 RFD21737 RFD21738 RFD21739 RFDANT RFD21742 RFD21743 RFD21772 RFD21773 KEYFOBs deficiency is present. If all of these conditions are met, RF Digital, at its sole option, will either replace or repair the RF Device or credit Customer's account for the amount the Customer paid to RF Digital for the RF Device. End of document. Free Applications Support * Email your application questions to support@rfdigital.com 76